{"id":71214,"date":"2016-11-08T00:00:00","date_gmt":"2016-11-08T05:00:00","guid":{"rendered":"http:\/\/lantechweb.wpengine.com\/blog\/securing-pallet-loads-stop-the-slide\/"},"modified":"2020-10-12T16:45:26","modified_gmt":"2020-10-12T20:45:26","slug":"securing-pallet-loads-stop-the-slide","status":"publish","type":"post","link":"https:\/\/www.lantech.com\/securing-pallet-loads-stop-the-slide\/","title":{"rendered":"Securing Pallet Loads: Stop the Slide"},"content":{"rendered":"

 <\/p>\n

Millions of loads slide off their pallets during shipment each year, resulting in\u00a0billions of dollars of damage and waste. These loads start their shipment journeys by being stretch wrapped,\u00a0a\u00a0process that’s\u00a0supposed to prevent this problem.<\/p>\n

<\/p>\n

Why do loads slide off their\u00a0pallets?<\/h3>\n\"securing\n

Because they\u2019re not adequately bonded to them.<\/p>\n

Most stretch wrappers, particularly turntable stretch wrappers, are adjusted to produce wrap patterns that apply stretch film stretch film all the way to the bottom of the pallet. All too often, this doesn\u2019t create a load-to-pallet bond strong enough to overcome the risks imposed by this set of problems:<\/p>\n

1. Vibration and Sudden Starts and Stops<\/h3>\n

They\u2019re inherent in truck and rail shipments. Unless attention is paid to the load-to-pallet bond, vibration can cause unitized loads to \u201cwalk off\u201d their pallets, given the opportunity. Sudden stops or starts can also cause unitized loads to slide off their pallets. Both situations create risk of damaged or unsalable products if there\u2019s room for the product loads to move or shift in trailers or rail cars.<\/p>\n

2. Stretch Film Punctures<\/h3>\n

Each time forklifts or pallet jacks pick up loads stretch wrapped to the bottom of their pallets, opportunities are created for something bad to happen because their forks punctured the\u00a0stretch film.<\/p>\n

There\u2019s a risk that the film punctures could spread from the vibration and multiple handlings during shipment and lead to load failure \u2013 resulting in\u00a0damage or unsalable products.<\/p>\n

How do you create a pallet bond without risking film punctures?<\/h3>\n

A film cable placed just below the top deck board of a pallet creates a secure load-to-pallet bond.\u00a0Rolling the bottom 5 inches of the film the film web into a tight cable during the last part of the stretch wrapper’s wrap cycle and driving it down onto the pallet — about an inch below its deck board — is the most effective way to bond or lock the load to the pallet.<\/p>\n

It\u2019s not the only way to bond a load to a pallet, but it\u2019s the way we recommend. This method works better than “regular” roping (when the film is bunched into an accordion-like rope) because it’s hard to position the regular rope just where you want it on the pallet — high enough to keep from being punctured by pallet jack or forklift forks and low enough to\u00a0bond or lock the load to the pallet<\/a>.<\/p>\n

Regular roping also tends to unbunch during the stress of shipment, which reduces its effectiveness. In fact, our research shows that a film cable bonding significantly outperforms\u00a0regular roping.<\/p>\n

A good rule of thumb is that every load that ships on a pallet should be bonded to it<\/h1>\n

There’s more than enough risk to go around in today’s world.<\/p>\n

Why take chances with your loads when there’s an easy, inexpensive, and effective way to improve their chances of arriving safely at their destinations?<\/p>\n

Learn more about\u00a0load-to-pallet bonding or\u00a0locking the load to the pallet by\u00a0watching this video<\/a>.<\/p>\n

You may be interested in these related posts:<\/span><\/p>\n