Extended Wrap Height
Increase the wrap heights of your loads. Replace the 2032 cm (80") mast with a 2794 cm (110") mast.
Makes a "cable" of film that locks the load to the pallet. The film cable decreases the risk of damage during shipment.
Use water at "city pressure" to clean the turntable. Make sure that the water can drain from the area.
Power Roller Stretch Plus - Film Delivery System (FDS)
Senses and adjusts the wrap force to the changes in the tension on the film. It is for a turntable speed more than 12 rpm, for very light or fragile loads, or for exact control of the wrap force.
220 V - 50/60 Hertz 15 AMP
Adds a transformer to the machine.
Operate in temperatures below -1 C to -18 C (+31 F to 0 F).
Put the load on the turntable with a forklift or a pallet jack.
EZ Weigh™ Integrated Scale
Weigh and wrap loads in one step with a scale built into the turntable.
Helps the operator align the load on the turntable.
It lets the operator put the load on the turntable at floor level. This is available for 1651 mm (65") and 1829 mm (72") turntables. Note: The customer must install this option.
Increase the length and width of your loads. A turntable with a 1829 mm (72") or 2438 mm (96") diameter is available. Note: The 2438 mm (96") turntable has a maximum of 8 rpm.
Operate in corrosive environment. It is for machines with exposure to agents such as salt and fertilizer.
Netting Film Delivery System (FDS)
Applies stretchable and non-stretchable netting. This is for loads that have a requirement for ventilation. Note: This FDS cannot use the standard stretch films.
Add a second turntable to increase efficiency. The operator can start the wrap cycle on the first turntable and put a load on the second turntable.
"Non Powered" Turntable Conveyor
The maximum load weight is 1814 kg (4000 lb). The maximum load dimensions are 1702 mm L x 1321 mm W x 1905 mm H (67" x 52" x 75"). The pass height is 178 mm (7").
Operate in temperatures of -29 C (-20 F).
"Non Powered" Conveyor
The maximum load weight is 1814 kg (4000 lb). The maximum load dimensions are 1524 mm L x 1321 mm W (60" x 52"). Note: This is for machines with the "Load on Turntable" option only. Note: You can add 1 or 2 sections of conveyor.
Auto Film Cut-off™
Automatically cuts the film at the end of the wrap cycle. This decreases labor on each load by approximately 30 seconds.
NEMA 12 Enclosure
Keeps moisture, dust, and dirt from electrical components.
Peak Production Speed Up to 25-35 Loads/Hr
Load Size Diagonal (Recommended) 1829 mm (72")
Maximum Load Wrap Height 2032 mm (80")
Maximum Load Weight 1814 kg (4000 lbs)Load Handling
Turntable Speed (Variable) 12 RPM
Turntable Size 1651 mm (65") Diameter
Turntable Drive 3/4 HP TEFCPerfomance Features
XT Cut and Clamp 5.0® Not Available
Auto Film Cut-Off™ Optional
Pallet Grip® Optional
Load Guardian Not Available
Standard Film Width 500 mm (20")
EZ Thread Film Delivery Standard
Standard Pre-Stretch 200%
Wrap Force Variable (Electric)
Film Capacity 250 mm (10") Roll Diameter
Film Delivery System Power Roller-Stretch
EZ Weigh Integrated Scale Optional
NEMA Type 1 Enclosure OptionalWeight and Size
Approx. Shipping Weight 658 kg (1450 lbs)
3023 mm L
1702 mm W
2337 mm H
(119" L x 67" W x 92" H)
Pneumatic Not Applicable
Dedicated Electric Service Req. US 120 VAC, 20 AMP
Dedicated Electric Service Req. EU 1L-220V-16AMP-50HzWarranty
Warranty Duration 5 Years, Unlimited Cycles, All Components Covered
11000 Bluegrass Parkway,
Louisville, KY 40299